How to Install a Bathtub
How to Install a Bathtub
Blog Article
Almost everyone maintains their own individual thinking with regards to How to Install a Bathtub.
Setting up a tub isn't exactly brain surgery, however it does need strong plumbing, woodworking, and often, tiling skills. Replacing an old bath tub with a new one is also a reasonably challenging task. If the old tub is conveniently easily accessible, the project can relocate immediately; if you have to open up a wall surface to remove the old bathtub as well as place the new bathtub, the job is much harder. In either instance, the project is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as set in the brand-new one. Ensure you have actually qualified yourself for the task and fit trying it. Instead of working with a professional to take over a halfway-completed task, it is much better to consider utilizing one before you start. Possibilities are you may require a professional plumber to make tube links.
This short article will certainly help you mount a brand-new bathtub in your shower room if you have currently purchased a brand-new tub and also don't require to alter the setup of your previous supply of water pipelines.
Your tools and also material list should make up the following:
Planning for the Installation
To start with, the supporting framework supplied with the bath needs to be fitted (if required) according to the maker's directions. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to ensure that if the faucet features a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the flexible tap connectors to the bottom of both faucets making use of 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you use all of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should now be ready to be fitted in its final setting.
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, then the first thing you ought to do is disconnect the supply of water. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be rather troublesome due to the restricted access that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a towel prepared for the staying water that will come from the pipes. As soon as the supply pipelines have actually been eliminated, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from turning during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old sealing substance.
Before moving on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Utilizing the two wood boards under its feet, position the tub in the needed setting. The wooden boards are helpful in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The next objective is to make sure that the tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub up until the spirit level reads degree.
To set up taps, fit all-time low of the outermost versatile tap adapter to the proper supply pipe by making a compression join; then do the very same for the other faucet.
Turn on the water supply and also check all joints and also new pipework for leakages as well as tighten them if essential. Fill up the bath tub and likewise check the overflow electrical outlet and the regular electrical outlet for leaks.
Ultimately, take care of the bathroom paneling as described in the supplier's instruction manual. Tiling and also sealing around the tub should wait up until the bath tub has been made use of at least when as this will resolve it right into its final placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end provides a connection to the current supply pipes.
If you need to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washing machines remain in place between the faucet and also the sink. Safeguard the tap in place with the maker supplied backnut. As soon as the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal tap ports. The previous kind should be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to crack a stiff seal, triggering the water to permeate the wall surface in between the bath as well as the tiling, bring about difficulties with wetness and possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes and cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the bath tub with water prior to securing, to permit the activity experienced when the tub is in use. The sealant can crack fairly early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
I came across that blog posting on How to Install a Bathtub when surfing the search engines. Sharing is caring. One never knows, you may very well be helping someone out. I appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Book Service Now Report this page